| |
|||||||
| |
|
|
|
|
|
|
|
| BraggAngle | false | false | Scalar | READ | Tango::DEV_DOUBLE | OPERATOR | |
| ExitOffset | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | |
| PhasingMode | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> Soft Phasing Mode\n1-> Forced Phasing Mode |
| Crystal | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Select the crystal type for the energy move. 0 -> CrystalSi111 1 -> CrystalSi311 2 ->Si111 ChannelCut 3 -> Si311 as Si111 (P01), Si111 as Si311 (P06), Si111 with par and perp offset (P10) |
| Position | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Monochromator Energy |
| UnitLimitMax | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Software limit for maximum Position |
| UnitLimitMin | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Software limit for minimum Position |
| PositionSim | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | |
| UpdateStatusRate | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Rate for checking status of the motors during a movement. |
| PositionAccuracy | false | false | Scalar | READ | Tango::DEV_DOUBLE | OPERATOR | Reads PositionAccuray from Bragg motor device and transforme it to eV. |
| ExitOffsetC1 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | EXPERT | ExitOffset to be restored when crystal is changed to 1 with the ChangeCrystalAndRecalibrate command. |
| ExitOffsetC0 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | EXPERT | ExitOffset to be restored when crystal is changed to 0 with the ChangeCrystalAndRecalibrate command. |
| MaskMoveMotors | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Masked motors will not be set the state to FAULT if they can not be moved. 1 (Perp) & 2 (Par) |
| PseudoChannelCutMode | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | If 1 the PseudoChannelCutMode is activated: \nparallel axis not moved for small angles. |
| BraggOffset | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Offset used only in p01 when the crystal Si311 is used as Si111 |
| BraggOffset0 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | EXPERT | Value to be restored in BraggOffset if crystal is changed to Si111 - crystal 0 (only for p01 and p06). |
| BraggOffset1 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | EXPERT | Value to be restored in BraggOffset if crystal is changed to Si311 - crystal 1 (only for p01 and p06). |
| BraggOffset3 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | EXPERT | Value to be restored in BraggOffset if crystal is changed to Si311 as Si111 - crystal 3 (only for p01 and p06). |
| ResultSim | false | false | Spectrum | READ | Tango::DEV_STRING | OPERATOR | |
| |
|||||||
| |
|
|
|
|
|
|
|
| ParInclination | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Error in the angle between first crystal and parallel axis. Used at p01 for computing paralell motor position. |
| ParInclinationP10 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Error in the angle between first crystal and parallel axis. Used at p10 if selected crystal is 3 |
| BraggOffsetP10 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | BraggOffset used at p10 if selected crystal is 3 |
| PerpOffsetP10 | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Offset in the perperdicula position at p10 if selected crystal is 3. |