| |
|||||||
| |
|
|
|
|
|
|
|
| ReadoutSpeed | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Set readout speed. Read last set value. Sets pixel clock to [0..6] 0 -> 1 MHz 3 -> 3 MHz 5 -> 500 kHz 6 -> 50 kHz |
| ExposureTime | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Set exposure time, read last set value. |
| BinningX | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Number of pixels [1...numPixelInX] to be binned in x-direction (if supported by CCD). 0 -> no binning |
| BinningY | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Number of pixels [1...numPixelInY] to be binned in y-direction. 0 -> no binning |
| Gain | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> Low ( Max. Dyn. Range ) 1 -> Std ( High Sensitivity ) |
| CapacityMode | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> Standard ( Low Noise ) 1 -> Extended ( High Signal ) |
| CropModeX | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Number of columns to readout |
| CropModeY | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Number of lines to readout |
| CropMode | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 1 -> active |
| CoolingTemperatureLevel | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Adjust temperature of CCD sensoR |
| CoolingOffOn | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | Switch temperature control off/on (0/1) |
| SensorTemperature | false | false | Scalar | READ | Tango::DEV_LONG | OPERATOR | |
| BacksideTemperature | false | false | Scalar | READ | Tango::DEV_LONG | OPERATOR | |
| FileDir | false | false | Scalar | READ_WRITE | Tango::DEV_STRING | OPERATOR | Path to the dector image files. |
| FilePrefix | false | false | Scalar | READ_WRITE | Tango::DEV_STRING | OPERATOR | The prefix of the image files to be created. The full image file name will be composed as prefix_number.postfix when acquiring images. |
| FileStartNum | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | The file number used when saviing an image. |
| BiasCorrection | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> disable, 1->enable |
| SyncOutput | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 1 -> Sets the ?SYNC? TTL trigger output to TTL high level. 0 -> Sets the ?SYNC? TTL trigger output to TTL low level. |
| OpenShutter | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> close 1 -> open 2 -> auto shutter |
| ShutterOpenTime | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Time to wait before the start of the exposure to ensure that the shutter is fully opened. |
| ShutterCloseTime | false | false | Scalar | READ_WRITE | Tango::DEV_DOUBLE | OPERATOR | Time to wait after exposure and before starting the readout to ensure that the shutter is fully closed. |
| SyncOutputEnabled | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> sync-output disabled 1 -> sync-output enabled |
| ShutterControlEnabled | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> shutter control disabled 1 -> shutter control enabled |
| TriggerMode | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | 0 -> internally triggered |
| TriggerTimeout | false | false | Scalar | READ_WRITE | Tango::DEV_FLOAT | OPERATOR | Trigger timeout in seconds. Only used if trigger mode is 1 |
| LastSavedImage | false | false | Scalar | READ | Tango::DEV_STRING | OPERATOR | Complete path of the last saved image |
| SaveImageFiles | false | false | Scalar | READ_WRITE | Tango::DEV_LONG | OPERATOR | If 0 image files are not saved |
| Image | false | false | Image | READ | Tango::DEV_USHORT | OPERATOR | |